Care of a Mishaum Point Beetle Cat

Storage

Storage under cover in an unheated garage, barn, or shed, with the boat right-side-up is best. Put two blocks under the keel, one eighteen inches forward of the centerboard slot and the other about eighteen inches forward of the stern along the skeg. To keep the boat upright (level side-to-side), put a chock under each side of the boat at the widest part of the boat and touching on the turn of the bilge.

If the boat must be left outside, keep it in the shade and avoid putting it on blacktop. Cover with a "breathable" tarpaulin or a simple roof. Do not allow the cover to lay directly anywhere on the canvas deck.

A Beetle Cat may be stored on a trailer provided the trailer properly supports the hull.

The older, non-plywood centerboards will stay straighter if left in position in the boat for the winter. Plywood centerboards and rudders should be stored in a standing position so the air reaches them from each side.

Spars should be placed on racks or blocking on the floor so as to be supported in two or three places. It is best if the sun does not beat directly on them.

Spring Commissioning

General

Your work place should be out of the weather and out of direct sunlight. Direct sunlight will open the seams very quickly. Some owners prefer to roll the boat over for hull work, but this is not necessary. With a narrow sawhorse located about eighteen inches forward of the centerboard slot and a wider sawhorse (at least five feet) located about two feet forward of the stern along the skeg, the boat can be rocked back and forth to allow all surfaces to be easily sanded and painted. If the sawhorses are 24" high, the boat should tip far enough to allow the board to be removed. If you need to get inside the boat, be sure it is extremely stable and secure.

Topsides

A good sanding is needed for good adhesion and smooth finish. Use 120, 150, or 180 grit sandpaper, depending on condition. Bulging putty or seam compound may be sanded off using 100 grit sandpaper over a block. If seems need any putty, use one made specifically for seams (stays soft). If seams are open due to drying out, minimal seam compound should be used since it will squeeze out when swelling occurs. A well maintained topside may require only one coat of marine enamel. Spots of bare wood may be "spot primed" with flat primer before finish coating. Depending on the starting conditions nd finish desired, a full coat of primer and / or a second coat of marine enamel may be needed. A thorough vacuuming and tack rag treatment between coats will provides the most blemish-free finish. A standard oil-base marine enamel is suggested. Polyurethanes and two-part paints are not recommended.

Bottom

Preparation is the same as for topsides except that coarser sandpaper mat be used. Bottom paint is its own primer. If you remove the centerboard, you may paint the whole board and also up inside the centerboard box.If you do, paint at least 8 inches up inside using a rag on a stick or a special 1" diameter roller (available at specialty paint stores).

Deck

It is not necessary to paint the deck every year. If you do paint, clean and sand lightly with 180 grit sandpaper and apply one coat of marine enamel, perhaps thinned a little. As with the topsides, a standard oil-base marine enamel is suggested. As the paint begins to build up over the years, a little 'non-skid compound' added to the paint will provide better footing on the deck.

Cockpit

It is not necessary to paint the cockpit every year. If you do, scrape away any loose paint and give a good hard sanding with 100 or 120 grit sandpaper. Spot prime any bare spots. When dry, apply one coat of marine enamel, perhaps thinned a little. Heavy buildup of paint may lead to peeling and blistering.

Bilge

It is good practice to clean out the bilge every year. A light scraping and thorough vacuuming will do the job. Some owners paint the bilge every few years. If you paint, scrape and sand thoroughly, vacuum, and paint one coat of cockpit or special bilge paint, perhaps thinned a little.

Briqhtwork and Spars

An extremely good sanding with 180 or 220 grit sandpaper is necessary to get the top surface clean and smooth. Be sure every surface is scratched. Any worn or peeling spots should be sanded to bare wood and primed with a 50/50 mixture of turpentine and spar varnish. A true 'spar varnish' should be used with polyurethanes and two-part finishes avoided. A minimum of two coats should be applied each year. A thorough vacuuming and tack rag treatment between coats will provides the most blemish-free finish.

Rigging

Running rigging should be checked each Spring and replaced if worn or frayed. The following dimension may be helpful: Throat 40 Feet Peak 46 Feet Peak (2 Block Rig) 62 Feet Main Sheet 46 Feet Gaff Bridle 42 Inches